Material Safety Data Sheet
Product No. 19975 Neutra-Form™
Issue Date (10-31-05)
Review Date (03-14-07)
Section 1: Product and Company Identification
Product Name: Neutra-Form™
Synonym: Tissue-Tek® NEUTRA-FORM™
Manufactured For: Sakura Finetek U.S.A., Inc.
Company Name
Ted Pella, Inc. and PELCO International, P.O. Box 492477, Redding, CA
96049-2477
Domestic Phone (800) 237-3526 (Mon-Thu. 6:00AM to 4:30PM PST; Fri 6:00AM
to 4:00PM PST)
International Phone (01) (530) 243-2200 (Mon-Thu. 6:00AM to 4:30PM PST; Fri 6:00AM to 4:00PM PST)
Chemtrec Emergency Number 1-800-424-9300 24 hrs a day.
Section 2: Composition / Information on Ingredients
|
Principle Hazardous Component(s)
|
% |
OSHA mg/m3 |
ACGIH |
NTP |
IARC |
OSHA |
|
Trade secret-chemical identity withheld |
Trade secret |
5 |
5 |
No |
No |
No |
Section 3: Hazard Identification
Emergency overview
Appearance: Whitish powder
Immediate effects: Irritation
Target organs: Respiratory tract, eyes.
Potential health effects
Primary Routes of entry: Inhalation and eye contact.
Signs and Symptoms of
Overexposure:
Eyes: Depending on the quantity that comes in contact with an eye, the injuries
sustained may range from mild irritation to redness and burning.
Skin: Exposure causes skin irritation, redness, and burning. Pre-existing skin conditions could be aggravated. Absorption through skin is unlikely.
Ingestion: Single dose oral toxicity is moderate. Symptoms may include stomach irritation, nausea, and diarrhea.
Inhalation: Dust can cause irritation of nasal and respiratory passages.
Chronic Exposure: ND
Chemical Listed As Carcinogen Or Potential Carcinogen: IARC, NTP, and OSHA do not list chemical ingredients as a carcinogen.
See Toxicological Information (Section11)
Potential environmental effects
See Ecological Information (Section 12)
Section 4: First Aid Measures
If accidental overexposure is suspected
Eye(s) Contact: Flush eyes immediately with water for 10 - 15 minutes. If burning persists, seek medical care.
Skin Contact: Contaminated clothing should be removed immediately. The affected body areas should be flushed with water for a period of approximately 15 minutes. If symptoms persist, seek medical attention.
Inhalation: The patient should be transported away from exposure and brought to fresh air. If necessary administer CPR, keep warm and quiet. Seek immediate medical attention.
Ingestion: Induce vomiting to conscious victims and seek medical attention. Unconscious victims should be placed on their left side with their head down. Do not induce vomiting.
Note to physician
Treatment: ND
Medical Conditions generally Aggravated by Exposure: ND
Section 5: Fire Fighting Measures
Flash Point: > 200 °F
Flammable Limits: ND
Auto-ignition point: ND
Fire Extinguishing Media: Water fog, regular foam, dry chemicals or carbon dioxide.
Special Fire Fighting Procedures: Wear self-contained breathing apparatus with full body protection.
Unusual Fire and Explosion Hazards: ND
Hazardous combustion products: None
DOT Class: Not regulated
Section 6: Accidental Release
Measures
Steps to be Taken in Case Material is Released or Spilled: Small and Large
Spills: With clean dry shovel, carefully place material into clean, dry
container and cover; remove from area. Flush spill area with water.
Waste Disposal Methods: Dispose of waste according to Federal, State and Local Regulations.
Section 7: Handling and
Storage
Precautions to be Taken in Handling and Storage: Suitable for any general chemical
storage area. All electrical equipment in storage and/or handling areas should
be installed in accordance with applicable requirements of the National
Electrical Code (NEC).
Storage temperature: ND
Storage Pressure: ND
Section 8: Exposure Controls / Personal Protection
Engineering Controls
Ventilation required: General mechanical or local exhaust should be used to maintain low exposure levels.
Personal Protection Equipment
Respiratory protection: Avoid prolonged periods of directly breathing vapors. In absence of proper environmental controls, the use of a NIOSH/OSHA respirator is recommended. Respirator use should comply with OSHA 29 CFR 1910.134.
Protective gloves: Appropriate resistant gloves.
Skin protection: Laboratory work clothing.
Eye protection: Chemical splash goggles.
Additional clothing and/or equipment: ND
Exposure Guidelines
See Composition/Information on Ingredients (Section2)
Section 9 Physical and Chemical Properties
Engineering Controls
Ventilation required: General mechanical or local exhaust should be used to maintain low exposure levels.
Personal Protection Equipment
Respiratory protection: Avoid prolonged periods of directly breathing vapors. In absence of proper environmental controls, the use of a NIOSH/OSHA respirator is recommended. Respirator use should comply with OSHA 29 CFR 1910.134.
Protective gloves: Appropriate resistant gloves.
Skin protection: Laboratory work clothing.
Eye protection: Chemical splash goggles.
Additional clothing and/or equipment: ND
Exposure Guidelines
See Composition/Information on Ingredients (Section2)
Section 9 Physical and Chemical Properties
Appearance and Physical State: Whitish powder
Odor (threshold): ND
Specific Gravity (H2O=1): >1
Vapor Pressure (mm Hg): ND
Vapor Density (air=1): ND
Percent Volatile by volume: ND
Evaporation Rate (butyl acetate=1): ND
Boiling Point: ND
Freezing point / melting point: ND
pH: >6 after neutralization
Solubility in Water: ND
Molecular Weight: ND
Section 10: Stability and Reactivity
Stability: Stable
Conditions to Avoid: ND
Materials to Avoid (Incompatibility): Avoid contact with strong mineral acids and strong oxidizing agents.
Hazardous Decomposition Products: None
Hazardous Polymerization: Will not occur
Section 11: Toxicological Information
Results of component toxicity test performed: ND
Human experience: ND
This product does not contain any compounds listed by NTP or IARC or regulated by OSHA as a carcinogen.
Section 12: Ecological Information
Ecological Information: Aquatic Bioassay was conducted using guidelines prescribed in “Static Acute Bioassay Procedure for Hazardous Waste for Samples,” result status = pass, 96 hour LC50 > 750 mg/l. Neutra-Form™ is within the allowable limits specified in 40 CFR 261 and 433.11, California Soluble Threshold Limit Concentrations (STLCs) and Total Threshold Limit Concentration (TTLCs) and is considered a non-hazardous material.
Chemical Fate Information: ND
Section 13 Disposal Considerations
RCRA 40 CFR 261 Classification: ND
Federal, State and local laws governing disposal of materials can differ. Ensure proper disposal compliance with proper authorities before disposal.
Section 14: Transportation Information
US DOT Information: Proper shipping name: Not regulated
IATA: Proper shipping name: Not regulated
Domestic shipments only:
IMO: Proper shipping name: Not regulated
Marine Pollutant: No
Canadian TDG: ND
IMDG Page: ND
Limitations: ND
Section 15: Regulatory Information
United States Federal Regulations
MSDS complies with OSHA’s Hazard Communication Rule 29, CFR 1910.1200.
SARA: Not listed
SARA Title III: Not listed
RCRA: Not listed
TSCA: Not listed
CERCLA: Not listed
State Regulations
California Proposition 65: None
International Regulations
Canada WHMIS: ND
Europe EINECS Numbers: ND
Section 16: Other Information
Label Information: ND
European Risk and Safety Phrases: ND
European symbols needed: ND
Canadian WHMIS Symbols: ND
Hazard Rating: Health: 1; Fire: 0; Reactivity: 0
(0=least, 1=Slight, 2=Moderate, 3=High, 4=Extreme)
Abbreviations used in this document
NE= Not established
NA= Not applicable
NIF= No Information Found
ND= No Data
Disclaimer
Ted Pella, Inc. makes no warranty of any kind regarding the information
furnished herein. Users should independently determine the suitability and
completeness of information from all sources. While this data is presented in
good faith and believed to be accurate, it should be considered only as a
supplement to other information gathered by the user. It is the User's
responsibility to assure the proper use and disposal of these materials as well
as the safety and health of all personnel who may work with or otherwise come
in contact with these materials.
MSDS Form 0013F1 V2