---

Home Page

Section 3 Hazardous Ingredients Data:
The ingredients below have been associated with one or more of the listed immediate and/or delayed (*) health hazards. Risk of damage and effects depends upon duration and level of exposure. BEFORE USING OR HANDLING, READ AND UNDERSTAND THE MSDS.
Signal Word CAUTION!
This material is a "health hazard" and/or a "physical hazard" as determined when reviewed according to the requirements of the Occupational Safety and Health Administration 29 CFR Part 1910.1200 "Hazard Communication" Standard.
Ethyl 2-cyanoacrylate:
OSHA PEL: None established
ACGIH TLV: None established
Carcinogen: Not listed by NTP, IARC or OSHA as of date of issuance of this document.
Chemical Hazard Rating: Health=2 (moderate), Fire=2(moderate), Reactivity=1 (slight)

Section 4 Fire and Explosion Hazard Data:
Combustible. Keep away from heat and flame.
Flash Point: 83°C
Auto Ignition Temp.: Not available
Flammable Limits (% by vol.): LEL 1.7; UEL No data
Fire Extinguishing Media: water spray, dry chemical, foam or CO2. Use water to keep fire-exposed containers cool.
Unusual Fire and Explosion Hazards: None known

Section 5 Immediate Health Hazard Data:
Inhalation: May be harmful if inhaled. Liquid or vapor may cause irritation of nose, throat and lungs.
Skin: Bonds skin instantly.
Skin Absorption: No hazards known
Eyes: Causes irritation
Ingestion: No hazards known

Section 6 Emergency First Aid Procedures:
Inhalation: Remove to fresh air. If not breathing, give artificial respiration, preferably mouth-to-mouth. Call a physician.
Ingestion: If accidentally swallowed, dilute by drinking large quantities of water. Immediately contact poison control center or hospital emergency room for any other additional treatment directions.
Skin Contact: If skin bonding occurs, peel, do not pull apart; soak in nail polish remover containing acetone if necessary.
Eye Contact: If eye contact occurs, flush with water only for 15 minutes and GET MEDICAL ATTENTION. Do not use any solvents to flush the eye and its surroundings.

Section 7 Reactivity Data:
Stability: Normally stable, but may become unstable at high temperatures or may react with water.
Hazardous Polymerization: Will not occur.
Incompatibilities: Water, alcohols, amines, bases and direct UV.
Hazardous Decomposition Products: Oxides of Carbon
Other Hazards: None known

Section 8 Control Measures:
If airborne contaminants are generated when the material is heated or handled, sufficient ventilation in volume and air flow patterns should be provided to keep air contaminant concentration levels below acceptable criteria.
Engineering Controls: The following exposure control techniques may be used to effectively minimize employee exposure; local exhaust ventilation, enclosed system design, process isolation and remote control in combination with appropriate use of personal protective equipment and prudent work practices. These techniques may not necessarily address all issues pertaining to your operations. We, therefore, recommend that you consult with experts of your choice to determine whether or not your programs are adequate.

Section 9 Personal Protection Information:
Protective Gloves: Wear impervious gloves as required to prevent skin contact.
Eye Protection: Use goggles if contact is likely.

Section 10 Spill or Leak Procedures:
Eliminate all ignition sources.
Soak up with absorbent material and remove to a chemical disposal area. Prevent entry into natural bodies of water.

Section 11 Waste Disposal:
Recover free liquid. Absorb residue and dispose of according to local, state/provincial, and federal requirements.
Empty Container: May contain explosive vapors. DO NOT cut, puncture or weld on or nearby.

Section 12 Handling Precautions:
Inhalation: Avoid breathing vapor.
Use with adequate ventilation.
Skin: Avoid contact with skin.
Eyes: Avoid contact with eyes.
Handle in accordance with good industrial hygiene and safety practices. These practices include avoiding unnecessary exposure and removal of the material from eyes, skin and clothing.
Wash thoroughly after handling.

Section 13 Storage Precautions:
Keep away from amines.
Store in cool, dry area away from sun and heat.
Keep containers tightly closed.
Exposure to small amounts of moisture, even moisture in air, causes polymerization and renders the product unusable.
Keep away from heat, sparks, flame and other ignition sources.