Interchangeable
Modular SEM Specimen Holders

This specimen holder is made of aluminum with spring-loaded clamping and grounding pin. Accommodates a sample thickness up to 3mm. Pin provides minimal surface clamping area and grounding on the imaged surface. Short Button Adapter (15372) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15375-2	Single flat sample clip holder, M4	each	$100.00	Qty:

This specimen holder is made from aluminum with spring-loaded clamping and grounding pin. Accommodates three samples with thickness up to 3mm. The pins provide minimal surface clamping area and grounding on the imaged surface. Short Button Adapter (15372) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15376-2	Triple Flat Sample Clip Holder, M4	each	$360.00	Qty:

This Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 45° angle.  Clip width is 6.35mm. Accommodates a sample thickness up to 11mm. The clip provides minimal surface clamping area and grounding on the imaged surface. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15460	45° Cross Section Holder, M4	each	$100.00	Qty:

The Triple Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 45° angle.  Clip width is 6.35mm. Accommodates three samples with a thickness up to 11mm. The clips provide minimal surface clamping area and grounding on the imaged surface. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15461	Triple 45° Cross Section Holder, M4	each	$250.00	Qty:

This Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 70° angle.  Clip width is 6.35mm. Accommodates a sample thickness up to 11mm. The clip provides minimal surface clamping area and grounding on the imaged surface. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15377-2	70° Cross Section Holder, M4	each	$100.00	Qty:

The Triple Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 70° angle.  Clip width is 6.35mm. Accommodates three samples with a thickness up to 11mm. The clips provide minimal surface clamping area and grounding on the imaged surface. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15379-2	Triple 70° Cross Section Holder, M4	each	$250.00	Qty:

This Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 90° angle.  Clip width is 6.35mm. Accommodates a sample thickness up to 11mm. The clip provides minimal surface clamping area and grounding on the imaged surface. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15378-2	90° Cross Section Holder, M4	each	$100.00	Qty:

The Triple Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 90° angle. Clip width is 6.35mm. Accommodates a sample thickness up to 11mm. The clips provide minimal surface clamping area and grounding on the imaged surface. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15380-2	Triple 90° Cross Section Holder, M4	each	$250.00	Qty:

This specimen holder holds thin or flat samples up 6.35mm (1/4"). Adjustable angle from 0-180°.
Made of non-magnetic stainless steel. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397). Overall height is 30mm (1.2") from the pivot point. The clamping part is a 16mm (0.62") cube w/o thumb screws.

Prod #	Description	Unit	Price	Order / Quote
15325-4	Cross Section Holder, M4	each	$90.00	Qty:

Designed to adjust the exact viewing angle for cross section made from wafers or other thin specimens up to a thickness of 3.2mm (1/8"). Angle adjustment range 0-90°. Made of aluminum with stainless steel allen screw. Allen wrench included. Extended Button ( 15372-10) is needed when used with the Dovetail Stage Adapters ( 15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15356-4	Adjustable Profile Holder, M4	each	$120.00	Qty:

This Compact Variable Tilt Specimen Mount allows for easy mounting and tilting small samples from 0° – 90° and SEM investigation with small working distances. Markings for 30°, 45°, 70° and 90°.  Table size is 11 x 11mm (0.46" x0.46"). Overall size is 14 x14 x12.7mm (0.55x0.55x0.5”). Made of aluminum with stainless steel screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15438	Compact Variable Tilt Mount, M4	each	$59.50	Qty:

Accommodates specimens pin stubs up to 18mm (.7") diameter or with a size up to 26 x 20mm. Tilts 0 - 90° with 10° markings. Additional markings for 30°, 45°, and 70°. Tilt table size is 26 x 20mm, overall size is 33 x 20 x 19mm H. Made of aluminum with stainless steel screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15450-4	Variable Tilt Specimen Holder, M4	each	$289.00	Qty:

Accommodates Hitachi 15mm cylinder mount with M4 thread. Tilts 0 - 90° with 10° markings. Additional markings for 30°, 45°, and 70°. Tilt table size is 26 x 20mm, overall size is 33 x 20 x 19mm H. Made of aluminum with stainless steel screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15451-4	Variable Tilt Specimen Holder for Hitachi M4 mounts, M4	each	$275.00	Qty:

Accepts 15mm Hitachi mounts on pin with M4 thread. Pin can be rotated and fixed for optimum position. When the pin with M4 thread is removed, this holder also accepts a standard 12.7mm (1/2") pin stub with 3.2mm (1/8") pin. 45° gives higher SE signal w/o tilting the specimen stage. Material: machined aluminum with stainless steel Allen set screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15428-45	45° Pre-Tilt Holder, M4	each	$47.50	Qty:

Accepts 15mm Hitachi mounts on pin with M4 thread. Pin can be rotated and fixed for optimum position. When the pin with M4 thread is removed, this holder also accepts a standard 12.7mm (1/2") pin stub with 3.2mm (1/8") pin. 70° EBSD Pre-Tilt Holder w/o tilting the specimen stage. Material: machined aluminum with stainless steel Allen set screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15428-70	70° Pre-Tilt Holder, M4	each	$52.00	Qty:

The Adjustable Spring-Loaded Vise Clamp holds various sizes and shapes of specimens. Vise clamps between 10 - 25mm. Made of vacuum grade aluminum and stainless steel. Vise size is 45 x 20mm. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15384-2	Adjustable Spring-Loaded Vise Clamp, M4	each	$350.00	Qty:

Holds a variety of specimens. The maximum gap is 11mm (7/16"). The jaws are 25.4mm (1") wide. Made of aluminum with stainless steel screw. Allen wrench included. Extended button (15372-10) is needed when used with the Dovetail stage adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15340-4	Micro Vise Holder, M4	each	$115.00	Qty:

closed position with pushrod in place


holding specimen in place with pushrod removed

Small Springloaded vise clamp for samples up to 12.7mm (1/2"). The jaws are 25mm (1") wide. Jaws also accommodate stainless steel pins for more awkward shaped samples. Removable pushrod for easy loading is provided. Material: machined aluminum with stainless steel pins and springs. Overall size w/o pushrod 30 x 25 x 12.5mm (1.18" x 1" x ½"). Extended button (15372-10) is needed when used with the Dovetail stage adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15341-4	Small Springloaded Vise Clamp, M4	each	$192.50	Qty:

Springloaded vise clamp for samples up to 26mm. The jaws are 25mm (1") wide. Jaws also accommodate stainless steel pins for more awkward shaped samples. Removable pushrods for easy loading are provided. Material: machined aluminum with stainless steel pins and springs. Overall size of vise clamp w/o pin and push rods 50 x 25 x 15mm (2 x 1 x 5/8"). Extended button (15372-10) is needed when used with the Dovetail stage adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15343-4	Springloaded Vise Clamp, M4	each	$300.00	Qty:

Universal Springloaded Vise

Springloaded vise clamp with reversible jaws for an opening up to 38mm. The universal jaws have special slots to firmly hold round samples of various diameters both horizontally and vertically. Maximum width of the jaws is 35mm. Material: machined aluminum with stainless steel springs, rods, screws and washers. Overall size of the vise clamp is 67 x 52 x 20mm (2.64" x 2" x 0.8"). M4 threaded hole in base. Extended button (15372-10) is needed when used with the Dovetail stage adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15342-4	Universal Springloaded Vise with Reversible Clamps, M4	each	$193.50	Qty:

PELCO^® Large Universal Vise Clamp

The large and extremely versatile vise clamp is intended for large and heavy samples or awkwardly shaped samples. Will clamp samples between 0-90mm. The two bases move 0-25mm. The array of holes take precision stainless steel 1/16" pins (10 pins are included) for either clamping the sample of for positioning the vise clamps (included). Overall size is 40W x 90L x 25mmH (1.6 x 3.5 x 1”). M4 threaded hole in the base. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15475-4	PELCO® Large Universal Vise Clamp, M4	each	$675.00	Qty:
15475-10	Replacement Vise Clamps for Large Universal Vise	pkg/2	115.00	Qty:
15475-20	Replacement Pins for Large Universal Vise, 3/4" long	pkg/10	32.50	Qty:

PELCO^® Bar Clamp Vise, 4", 6" and 8"

The PELCO^® Bar Clamp Vise is available in three lengths; 102mm (4"), 152mm (6") and 203mm (8") with the same clamps for each version. This bar type clamp can accommodate specimens up to 72mm (3"), 127mm (5") and 178mm (7") in length respectively. The jaws are reversible, offering different clamping options and they operate independently anywhere on the clamping bar. This will allow for positioning the region of interest of the specimen within the travel range of the SEM stage. Stainless steel 1/16" pins (6 pins are included) can be placed on the clamps for awkwardly shaped samples. Clamping bars and clamps can be purchased additionally to make up the best functional set for the job at hand. Made of vacuum grade aluminum with brass bar and brass thumbscrews and stainless steel type 316 dowels.

#15477-10

Overall size for the 102mm (4") version: LxWxH 102 x 22 x 19mm (4" x 7/8" x ¾") Overall size for the 152mm (6") version: LxWxH 152 x 22 x 19mm (6" x 7/8" x ¾") Overall size for the 203mm (8") version: LxWxH 203 x 22 x 19mm (8" x 7/8" x ¾") Extended button (15372-10) is needed when used with the Dovetail stage adapters (15371 or 15397). Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

PELCO® Technical Notes: PELCO® Bar Clamp Vise, 4, 6, and 8" (80KB PDF)

Prod #	Description	Unit	Price	Order / Quote
15477-4	PELCO® Bar Clamp Vise, 102mm (4"), complete with bar and two clamps, M4	each	$375.00	Qty:
15476-4	PELCO® Bar Clamp Vise, 152mm (6"), complete with bar and two clamps, M4	each	400.00	Qty:
15478-4	PELCO® Bar Clamp Vise, 203mm (8"), complete with bar and two clamps, M4	each	425.00	Qty:
15477-10	Additional Clamp for 102mm (4"), 152mm (6") or 203mm (8") bar	each	155.00	Qty:
15477-40	Additional 102mm (4") bar, M4	each	100.00	Qty:
15476-60	Additional 152mm (6") bar, M4	each	120.00	Qty:
15478-80	Additional 203mm (8") bar, M4	each	145.00	Qty:

Mini SEMclamp™ on a Ø15 x 10mm M4 cylinder mount. Convenient for holding flat or thin specimens such as Si chips, wires, foil and small tubes. Material: vacuum grade aluminum with brass screw.
Short Button (15372) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15494	PELCO Mini SEMClamp™ Ø15 x 10mm, M4	each	$21.60	Qty:

PELCO SEMClamp™ holder 15mm (0.6") long with 10mm (0.4") wide clamping area. Convenient holder for clamping down samples up to a thickness of 7mm under the clamping strips. Extended Button Adapter (15372-10) is needed when used with the Dovetail stage adapters (15371 or 15397). Overall dimensions 23x20x9mm (0.9"x0.78"x0.35"). Material: machined aluminum with brass screws.

Prod #	Description	Unit	Price	Order / Quote
15347-4	Small PELCO SEMClamp™ 15 x 10mm, M4	each	$86.00	Qty:

PELCO SEMClamp™ holder 25mm (1") long with 15mm (0.6") wide clamping area. Convenient holder for clamping down samples up to a thickness of 7mm under the clamping strips. Extended Button Adapter (15372-10) is needed when used with the Dovetail stage adapters (15371 or 15397). Overall dimensions 33x25x9mm (1.3"x1"x0.35"). Material: machined aluminum with brass screws.

Prod #	Description	Unit	Price	Order / Quote
15348-4	Medium PELCO SEMClamp™ 25 x 15mm, M4	each	$95.00	Qty:

PELCO SEMClamp™ holder 40mm (1.6") long with 20mm (0.8") wide clamping area. Convenient holder for clamping down samples up to a thickness of 7mm under the clamping strips. Short Button Adapter (15372) is needed when used with the Dovetail stage adapters (15371 or 15397). Overall dimensions 48 x 30 x 9mm (1.9 x 1.2 x 0.35"). Material: machined aluminum with brass screws.

Prod #	Description	Unit	Price	Order / Quote
15349-4	Large PELCO SEMClamp™ 40 x 20mm, M4	each	$96.00	Qty:

5mm recess allows for background free imaging and no contact with sample surface in imaging area. Clamping area is 25mm (1") long and 15mm (0.6") wide. Maximum thickness 7mm under the clamping strips. Extended Button Adapter (15372-10) is needed when used with the Dovetail stage adapters (15371 or 15397). Overall dimensions 33x25x11mm (1.3x1x0.43"). Material: machined aluminum with brass screws.

Prod #	Description	Unit	Price	Order / Quote
15346-4	Recessed PELCO SEMClamp™ 25 x 15mm, M4	each	$96.00	Qty:

Simple but effective design to hold wafers and thin samples up to 3.2mm (1/8). 15mm dia x 10mm H. Made of aluminum with stainless steel allen screws. Allen wrench included. Short Button (15372) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15335-4	Thin Specimen Split Mount Holder, M4	each	$24.00	Qty:

A small tube, needle or wire clamp based on a standard Ø15x10mm cylinder mount with M4 thread. Ideal for examining wire cross sections or needle tips. Holds wires, tubes and needles up to Ø2mm (0.008"); hole is 5mm (0.20") deep. Material: vacuum grade aluminum with a stainless steel set screw. Allen wrench included. Short Button (15372) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15490	Tube/Needle Clamp, Ø15x10mm, M4	each	$23.50	Qty:

Small set screw vise with an open slot of 4mm (.157") wide and 5mm (.197") deep. Ø15 x 12mm x M4. Material: machined aluminum with stainless steel allen set screw. Allen wrench included. Short Button Adapter (15372) is needed when used with the Dovetail stage adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
16335	Small Set Screw Vise, M4, Ø15 x 12mm H, M4	each	$21.95	Qty:

Large Set Screw Vise, Ø25mm

Large Set Screw Vise

Double Slotted Mini Vise

Double slotted set screw vise with 2 ea. 1mm wide x 3mm deep slots to clamp thin specimens or cross sections. Simple but effective design to hold wafers and thin samples up to 1mm (.039") thick. 15mm dia x 6mm H. Made of aluminum with 2 stainless steel allen set screws. Allen wrench included. Short Button Adapter (15372) is needed when used with the Dovetail stage adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
16341	Double Slotted Set Screw Vise, M4, Ø15 x 6mm H, M4	each	$21.40	Qty:

Double Slotted Mini Vise

Ø32mm Double slotted set screw vise with 2 ea. 1mm wide by 5mm deep slots. Dimensions Ø32x10mm (1-1/4" x 0.394"). Clamp thin specimens and cross sections without the need for tape or conductive paint. Material: machined aluminum with 2 stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
16313	Double Slotted Mini Vise, Ø32x10mm, M4	pkg/each	$39.90	Qty:

Large Double Slotted Set Screw Vise with 2 ea. 2.5mm by 5mm deep slots. Dimensions Ø25x10 mm (1 x 0.4"). Clamp thin specimens and cross sections without the need for tape of conductive paint. Material: machined aluminum with 2 stainless steel allen set screws. Allen wrench included. Short Button Adapter (15372) is needed when used with the Dovetail stage adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
16372	Large Double Slotted Set Screw Vise, Ø25mm x 10mm H, M4	each	$29.80	Qty:

Large Double Slotted Vise

Ø32mm Large double slotted set screw vise with 2 ea. 2.5mm wide by 5mm deep slots. Dimensions Ø32x10mm (1-1/4" x 0.394"). Clamp thin specimens and cross sections without the need for tape or conductive paint. Material: machined aluminum with 2 stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
16312	Large Double Slotted Set Screw Vise, Ø32x10mm, M4	pkg/each	$39.90	Qty:

Single Pin Stub Holders

For holding and viewing SEM mounts with the standard 3.2mm pin. Made of aluminum, includes a pin locking screw. Four different heights are available: 10, 25, 38 and 55mm. Short Button Adapter (15372) is needed when used with the Dovetail stage adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15363-1	Single Pin Stub Holder Ø15x10mm H, M4	each	$26.50	Qty:
15363-2	Single Pin Stub Holder Ø15x15mm H, M4	each	22.50	Qty:
15387-2	Single Pin Stub Holder Ø16x25mm H, M4	each	27.50	Qty:
15361	Single Pin Stub Holder Ø16x38mm H, M4	each	25.00	Qty:
15364	Single Pin Stub Holder Ø15x55mm H, M4	each	25.00	Qty:

Accommodates up to four standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with stainless steel set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397). Holder size is Ø31.8 x 11.25mm.

Prod #	Description	Unit	Price	Order / Quote
15310-4	Multi Holder for 4 Pin Stubs, M4	each	$49.00	Qty:

Multi Holder for 6 Pin Stubs

Accommodates up to six standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with stainless steel set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397). Holder size is Ø42 x 10.7mm (Ø1.65" x 0.42").

Prod #	Description	Unit	Price	Order / Quote
15411	Multi Holder for 6 Pin Stubs, M4	each	$75.00	Qty:

Multi Holder for 8 Pin Stubs

Accommodates up to eight standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with stainless steel set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397). Holder size is Ø50 x 10.7mm (Ø1.97" x 0.42").

Prod #	Description	Unit	Price	Order / Quote
15413	Multi Holder for 8 Pin Stubs, M4	each	$90.00	Qty:

Accommodates up to twelve standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with stainless steel set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397). Holder size is Ø62 x 10.7mm (Ø2.44" x 0.42").

Prod #	Description	Unit	Price	Order / Quote
15417	Multi Holder for 12 Pin Stubs, M4	each	$100.00	Qty:

Multi Holder for 29 Pin Stubs

Accommodates up to 29 standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with 302 type stainless steel springs to hold the pin stubs. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397). Holder size is Ø90 x 5mm (Ø3.5" x 0.2").

Prod #	Description	Unit	Price	Order / Quote
15418	Multi Holder for 29 pin stubs, M4	each	$234.50	Qty:

Multi Holder for 49 Pin Stubs

Accommodates up to 49 standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with 302 type stainless steel springs to hold the pin stubs. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397). Holder size is Ø117 x 5mm (Ø4.6" x 0.2").

Prod #	Description	Unit	Price	Order / Quote
15419	Multi Holder for 49 pin stubs, M4	each	$394.50	Qty:

Prod #	Description	Unit	Price	Order / Quote
15429	45° Multi Holder for 6 pin stubs, M4	each	$108.00	Qty:

Specimen holder for cylinders up to 22mm (7/8") diameter. Made of aluminum with stainless steel allen screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15402	Specimen holder for cylinders up to 22mm (7/8"), M4	each	$39.00	Qty:

Specimen holder for 1" or 25mm metallographic mounts. Made of aluminum with stainless steel allen screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15403	Metallographic Mount Holder, 1" or 25mm, M4	each	$46.00	Qty:

Specimen holder for 1-1/4" or 30mm metallographic mounts. Made of aluminum with stainless steel allen screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15404	Metallographic Mount Holder, 1-1/4" or 30mm, M4	each	$58.00	Qty:

Metallographic Mount Holder, 1-1/2" or 40mm

Specimen holder for 1-1/2" or 40mm metallographic mounts. Made of aluminum with stainless steel allen screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15405	Metallographic Mount Holder, 1-1/2" or 40mm, M4	each	$68.00	Qty:

Metallographic Mount Holder, 2" or 50mm

Specimen holder for 2" or 50mm metallographic mounts. Made of aluminum with stainless steel allen screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15406	Metallographic Mount Holder, 2" or 50mm, M4	each	$74.00	Qty:

Geological Thin Section Holder

Holds a standard geological thin section or slide of 47 x 27mm. 2 clips are provided for secure holding. Tweezer inserts enable easy loading. Overall dimensions are 55 x 30 x 8mm. Material: aluminum with copper clips and brass screws. Extended button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15431-4	Single Geological Thin Section Holder, M4	each	$216.00	Qty:

This variable size geological thin section holder holds either standard thin sections of 47 x 27mm or smaller or larger thin sections. Smallest size would be 40 x 20mm. Two clips are provided for secure holding. Tweezers insert enables easy loading. Overall dimensions are 51 x 32 x 8mm. Material: vacuum grade aluminum with copper clips and brass screws. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15435-4	Variable Size Geological Thin Section Holder, M4	each	$216.00	Qty:

Dual Geological Thin Section Holder

Holds two standard geological thin sections or slides of 47 x 27mm. Tweezer inserts enable easy loading. Clips are provided for secure holding. Overall dimensions are 55 x 58 x 8mm. Material: aluminum with copper clips and brass screws. Extended button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15432-4	Dual Geological Thin Section Holder, M4	each	$246.00	Qty:

Quadruple Geological Thin Section Holder

Holds four standard geological thin sections or slides of 47 x 27mm. Tweezer inserts enable easy loading. Clips are provided for secure holding. Overall dimensions are 107 x 58 x 8mm. Material: aluminum with copper clips and brass screws. Extended button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15434-4	Quadruple Geological Thin Section Holder, M4	each	$272.00	Qty:

Round Bulk Specimen Holder

The bulk specimen holder holds irregular and round specimens up to a diameter of 32mm (1-1/4"). Made of aluminum with two sets of stainless steel allen screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15308-4	Bulk Specimen Holder, M4	each	$85.00	Qty:

Large Round Bulk Specimen Holder

The large bulk specimen holder holds larger irregular and round specimens up to a diameter of 51mm (2"). Made of aluminum with two sets of stainless steel allen screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15423	Large Bulk Specimen Holder, M4	each	$104.00	Qty:

Straight Bulk Specimen Holder

Versatile specimen holder to clamp irregular or long shaped specimens. Opening is 15.9W x 25.4L x 9.5mm D (5/8" x 1" x 3/8"). Made of aluminum with stainless steel allen screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15320-4	Straight Bulk Specimen Holder, M4	each	$82.00	Qty:

Opening is 32mm (1 1/4") wide x 32mm (1 1/4") long x 13mm (1/2") deep. Material: machined aluminum with stainless steel allen set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15321-4	PELCO® Large Bulk Specimen Holder, M4	each	$96.00	Qty:

Opening is 52mm (2") wide x 40mm (1 1/2") long x 13mm (1/2") deep. Material: machined aluminum with stainless steel allen set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15322-4	PELCO® X-Large Bulk Specimen Holder, M4	each	$124.00	Qty:

Opening is 80mm (3-1/8") wide x 48mm (1-7/8") long x 13mm (1/2") deep. Material: machined aluminum with stainless steel allen set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15323-4	PELCO® XX-Large Bulk Specimen Holder, M4	each	$148.00	Qty:

Multipurpose Specimen Holder

Accepts up to 25.4mm (1") diameter specimens. The slotted design also allows for clamping elongated or rod shaped specimens. Made of aluminum with stainless steel allen screw. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15305-4	Multi Purpose Specimen Holder, M4	each	$62.00	Qty:

45°/90° Combination Holder

Combined specimen holder for 90° cross sections of wafers or thin samples up to 6.35mm (1/4") and a pin stub at 45°. Made of aluminum with stainless steel set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15358-4	45° / 90° Combination Holder, M4	each	$94.00	Qty:

TEM Grid Holder for 4 Grids

This TEM grid holder holds up to 4 TEM grids. It enables imaging and analyzing specimens on TEM grids in the SEM. For EDS applications it is beneficial to place thin films on a TEM grid or small particles on a TEM grid with a support film. This can significantly reduce background in the EDS spectrum and increase detection limits of the EDS detector. Opening angle on the holes in the top and base are 120° to reduce electron scattering and improve X-ray collection. Overall diameter is 18mm (0.7"), overall height is approximately 25mm (1") with a stand-off pin mounted on a ø15 x 10mmx M4 Hitachi mount. The stand-off pin minimizes electron and X-ray scattering contribution from the stage. TEM grid locations are numbered. Material: vacuum grade aluminum with brass screw.

Prod #	Description	Unit	Price	Order / Quote
15469-15	TEM Grid Holder for 4 Grids, M4	each	$196.00	Qty:

The E-Beam Lithography Mount comprises 2 PELCO SEMClips™ to hold the sample, a Faraday cup (ø2.5mm with 100µm hole) to measure the beam current and gold on carbon resolution sample (ø3mm) for resolution test all on a 25mm aluminum cylinder stub positioned in such a way to leave maximum sample space. M4 threaded hole in bottom. Material: Aluminum with copper clips and brass screws. The Gold on Carbon is similar to #617 with gold particle size range from approximately 5nm to 150nm. Shipped in plastic storage box. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
16405-4	E-Beam Lithography Mount, M4	each	$485.00	Qty:

A set of useful holders to quickly mount multiple standard Ø15mm Hitachi mounts with M4 thread on a base with M4 thread. Fully compatible with all Hitachi stage adapters using M4 threads and with all PELCO® Modular Stage Adapters. Available for 3 of 6 Hitachi mounts, flat or with 45° tilt for enhanced signal. Made of aluminum with stainless steel M4 threads. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15433	Triple Specimen Holder for 3 Hitachi mounts, Ø25x6mmxM4	each	$40.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15436	Multiple Specimen Holder for 6 Hitachi mounts, Ø35x6mmxM4	each	$76.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15437	Multiple Specimen Holder for 3 Hitachi mounts, Ø35x6mmxM4	each	$76.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15430-3	45° Tilt Triple Specimen Holder for 3 Hitachi mounts, Ø25x14mmxM4	each	$68.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15430-6	45° Tilt Multiple Specimen Holder for 6 Hitachi mounts, Ø35x14mmxM4	each	$115.00	Qty:

Multi Holder for 5 JEOL Stubs

Holds up to five 9.5mm JEOL cylinder mounts. Made of aluminum with stainless steel set screws. Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15315-4	Multi Specimen Holder for JEOL Stubs, M4	each	$62.00	Qty:

JEOL or ISI/ABT/Topcon mounts to Hitachi M4 mount

Small cylinder mount adapter accommodates JEOL or ISI/ABT/Topcon cylinder mounts up to 15mm diameter. Enables the use of Ø9.5 and Ø12.2mm JEOL or Ø15mm ISI/ABT/Topcon cylinder mounts on Hitachi M4. Made from aluminum with stainless steel screw, Allen wrench included. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
15401	Adapter Holder for Cylinder Mounts, M4	each	$36.00	Qty:

The PELCO SEMClip™ mounts can be used to hold flat thin samples with a thickness of 2mm. Made of aluminum with copper spring clips. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397). All SEMClip™ mounts in this section have M4 thread.

bottom

Prod #	Description	Unit	Price	Order / Quote
16324-10	PELCO SEMClip™, Ø15x6mm x M4 Cylinder Mount, 1 clip	each	$18.85	Qty:

Prod #	Description	Unit	Price	Order / Quote
16116-4-20	PELCO SEMClip™, Ø100x 5mm x M4 Cylinder Mount, 2 clips	each	$112.50	Qty:
16116-4-40	PELCO SEMClip™, Ø100x 5mm x M4 Cylinder Mount, 4 clips	each	128.50	Qty:
16116-4-60	PELCO SEMClip™, Ø100x 5mm x M4 Cylinder Mount, 6 clips	each	144.50	Qty:

Prod #	Description	Unit	Price	Order / Quote
16314-20	PELCO SEMClip™, Ø32x12mmxM4 Cylinder Mount, Double 90°, 2 clips	pkg/each	$39.90	Qty:

Prod #	Description	Unit	Price	Order / Quote
16241	PELCO SEMClip™, 12 x12x14mm H x M4, 4 sided clips	each	$56.50	Qty:

PELCO SEMClip™ Replacement Clips and Screws

Seven wafer holders for diameters varying from 1"-8" are available.  Made of aluminum with brass clips.  Each wafer holder has two fixed clips and one spring-loaded clip to secure the wafer on the holder (stainless steel pegs on the 25mm (1") holder). Cut-outs are provided for easy wafer removal (except for 5"). The 1" Wafer Holder uses two fixed tapered cones and one spring loaded tapered cone to hold the wafer. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

100mm dia. (4") Wafer Holder holding a silicon wafer 25mm dia. (1") Wafer Holder securing a wafer with tapered cones

Seven diameters available: 25mm (1"); 51mm (2"); 76mm (3"); 100mm (4"); 127mm (5"); 150mm (6"); 200mm dia. (8")

Prod #	Description	Unit	Price	Order / Quote
15388	Wafer Holder for 25mm dia. (1"), M4	each	$350.00	Qty:
15390	Wafer Holder for 51mm dia. (2"), M4	each	350.00	Qty:
15369	Wafer Holder for 76mm dia. (3"), M4	each	350.00	Qty:
15389	Wafer Holder for 100mm dia. (4"), M4	each	350.00	Qty:
15381	Wafer Holder for 127mm dia. (5"), M4	each	350.00	Qty:
15382	Wafer Holder for 150mm dia. (6"), M4	each	375.00	Qty:
15383	Wafer Holder for 200mm dia. (8"), M4	each	450.00	Qty:

Wafer Holders for Notch Style Wafers; 4 - 12"

Wafer holders for notch style wafers in 4", 6", 8" and 12" are available. Made of aluminum with brass clips. Each wafer holder has two fixed clips, a notch pin and a spring-loaded clip opposite the notch pin to secure the wafer on the holder. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

300mm (12")

150mm (6")

Prod #	Description	Unit	Price	Order / Quote
15393	Wafer Holder for notch style wafers, 100mm / 4", M4	each	$425.00	Qty:
15391	Wafer Holder for notch style wafers, 150mm / 6", M4	each	450.00	Qty:
15395	Wafer Holder for notch style wafers, 200mm / 8", M4	each	850.00	Qty:
15394	Wafer Holder for notch style wafers, 300mm / 12", M4	each	950.00	Qty:

Flat 63mm Sample Mount

Large flat mounting with 63mm diameter area for large sample or for mounting multiple samples with conductive adhesive. Made of aluminum. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
16114-4	Large 63mm Sample Mount, M4	each	$29.50	Qty:

Flat 100mm Sample Mount

Large flat mounting with 100mm diameter area for large sample or for mounting multiple samples with conductive adhesive. Made of aluminum. Extended Button (15372-10) is needed when used with the Dovetail Stage Adapters (15371 or 15397).

Prod #	Description	Unit	Price	Order / Quote
16116-4	Large 100mm Sample Mount, M4	each	$89.50	Qty: