Home Page Abbreviated Contents Customer Login Quick Order / View Order
Contact Us Search Indexes Finish Order

back to SEM Supplies and Accessories, page 1

Back to Carbon Products

Conductive Adhesives Tabs, Tapes and Sheets
Carbon, Aluminum, Copper, Silver

Conductive Adhesives for Scanning Electron Microscopy
PELCO Tabs™, Carbon Conductive Tabs, Double Coated
PELCO® Image Tabs
Carbon Conductive Tape, Double Coated
Conductive Lift-N-Press Tabs, Double Sided
Carbon Conductive Tapes, Double Coated
3M™ XYZ Axis Electrically Conductive, Double Sided Tape, 9712 and 9713
3M™ Copper Conductive Tapes, Single Adhesive Surface
3M™ Copper Conductive Tape, Double Coated
Copper Tape with Nickel, Single Adhesive Surface
3M™ Aluminum Conductive Tape, Single Adhesive Surface
Carbon Conductive Adhesive Sheet, Double Adhesive Coated
Silver Conductive Adhesive Sheet, Double Adhesive Coated
Cleanroom, High Temperature Electro Static Dissipative Tape
Low Static, High Temperature Tape

carbon conductive tabs

Technical Information about Conductive Carbon Tabs

PELCO Tabs™, Carbon Conductive Tabs, Double Coated

new types added

The simplicity of application, and smooth, clean surfaces of the static-free PELCO Tabs™, Carbon Conductive Tabs are a significant improvement compared to many of the other common adhesives that have been used in microscopy mounting. Both tab sides have a thick conductive adhesive (conductive inner film is 35µm and the adhesive is 45µm on each side for a total of 125µm [5 mils]) with a liner on both sides, a transparent liner and white liner respectively. They are ready for immediate use. On the other hand, the top liner does not have to be removed until the sample is ready to be mounted. This reduces possible contamination. Outgassing is negligible.

Application of the tab to a mount or surface may be done slowly and carefully to maintain surface smoothness.

The conductive adhesive is a carbon filled acrylic glue, free of solvents. It can be removed from the specimen mount with ethyl acetate, ethanol, isopropanol or alcohols. Temperature maximum is 60°C (140°F). Small impurities of Si, Sb, S and very small impurities of Fe, Mg and Na can be found.

This product may also be used for gunshot residue analysis.

Many laboratories use these tabs for SEM in a large diversity of applications. Refrigeration will increase shelf life but a warm up period of one hour is then required before use. The specimen should be placed on the surface under the white liner.

(Use Spectro-Pure Tabs where necessary – see below).
MSDS
New - Now Available in 4 sizes

Prod #DescriptionUnitPriceOrder / Quote
16084-6
PELCO Tabs™, Carbon Conductive Tabs, 6mm OD
pkg/100
$14.50
Qty:
16084-3
PELCO Tabs™, Carbon Conductive Tabs, 9mm OD
pkg/98
14.50
Qty:
16084-1
PELCO Tabs™, Carbon Conductive Tabs, 12mm OD
pkg/100
14.50
Qty:
16084-2
PELCO Tabs™, Carbon Conductive Tabs, 25mm OD
pkg/54
29.90
Qty:

"Spectro Tabs" When you need higher purity carbon

A need existed for a tab with a purer composition in situations such as X-ray analysis. The EDX graph shows a cleaner and smoother surface for those applications that require critical composition study.

Prod #DescriptionUnitPriceOrder / Quote
16084-4
Spectro Tabs, higher purity conductive carbon tabs,12mm O.D.
pk/120
$31.00
Qty:

back up

PELCO® Image Tabs™, 260µm (10mil) Carbon Conductive Tabs, Double Coated

Back by popular demand, the thicker PELCO® Image Tab is a return to the stiff 260µm (10mil) thick smooth conductive tab. Though not as conductive or sticky as the current 4mil PELCO Tabs, the Image Tab is suitable as a photographic background and is repositionable. This tab is also suitable for Jet Scan applications where the tab must be removed and archived. The Image Tab's surface is less prone to bubbling and cracking when metal coated under vacuum and thus better than the 125µm (5mil) PELCO® Tab as a photographic background for small particles like pollen and insect parts.

Both sides of the 200µm thick conductive polycarbonate base have 30µm thick conductive glue. Total thickness is 260µm with a liner on both sides. Protection for handling, storage and shipping is provided on one side by the transparent liner sheet and on the other side by the white liner cover.

The conductive adhesive is a carbon-filled acrylic glue, free of solvents. It can be removed from the specimen mount with ethyl acetate, ethanol, isopropanol or alcohols. Temperature maximum is 60°C (140°F). Small impurities of Ni, Cu, Si, Sb, S, Na, P and very small impurities of Fe and Mg can be found. Refrigeration will increase shelf life but a warm-up time of 1 hour is then required before use.

Prod #DescriptionUnitPriceOrder / Quote
16084-20
PELCO Image tabs,12mm O.D.
pk/100
$16.50
Qty:

back up
Carbon Conductive Tape

Carbon Conductive Tape, Double Coated

Both sides of the 200µm thick conductive polycarbonate base have 30µm thick conductive glue. Total thickness is 260µm.
Protection for handling, storage and shipping is provided on one side by the 25µm thick, transparent liner and on the other side by the 40µm thick, white liner.
The conductive adhesive is a carbon–filled acrylic glue, free of solvents. It can be removed from the specimen mount with ethyl acetate, ethanol, isopropanol or alcohols. Temperature maximum is 60°C (140°F). Small impurities of Cu, Si, Sb, S, Na, P and very small impurities of Fe and Mg can be found. Refrigeration will increase shelf life but a warm-up time of 1 hour is then required before use. Sizes are 12mm and 25mm W x 5m L (1/2" and 1" x 5.46 yrd) with a core diameter of 76mm (3"). Also available in sheet form: 65 W x 300mm L (2.5" x 11.8").

Please observe that 16084-9 carbon conductive tape, 65mm wide, might be applied for particle collection and analysis in clean rooms or other purposes.

Prod #DescriptionUnitPriceOrder / Quote
16084-7
Carbon Conductive Tape, 12mm W x 5m L
each
$64.00
Qty:
16084-8
Carbon Conductive Tape, 25mm W x 5m L
each
75.00
Qty:
16084-9
Carbon Conductive Tape in sheet form, 65mm W x 300mm L
each
27.50
Qty:

back up

lift-n-press adhesive Tabs

Conductive Lift-N-Press Adhesive Tabs, Double Sided

Composed of a thin film of strong conductive adhesive approx. 1/2" (12.7mm) dia.; >99% transparent to EDS, with 0.6% nickel and <0.3% copper content. To apply, place "Press" portion of tab on SEM mount surface, lift "Lift Off" tab and peel, slightly rotating tab when lifting. Can be cut to size as desired.

Prod #DescriptionUnitPriceOrder / Quote
16083
Conductive Lift-N-Press, roll/250
each
$33.95
Qty:

back up
 carbon conductive tape

Carbon Conductive Tapes, Double Coated

These carbon tapes are conductive and may be used conveniently for scanning electron microscopy or EDS applications.
This is the same material as the PELCO Tabs™, Carbon Conductive Tabs (top of page), but in tape form. The tape form allows for special application uses such as custom sizes, cut-outs and shapes. The purity of this tape is identical to the standard tab form at top of page.
Both sides of the tape have a thick conductive adhesive (conductive inner film is 35µm and the adhesive is 45µm on each side for a total of 125µm [5 mils]) with a white liner. The double adhesive and conductive design permits quick mounting of samples without using liquid or colloidal adhesives.
The tape is relatively solid and non-porous and does not absorb small samples. The variety of widths affords efficient application to various specimen mount surface sizes. Thickness is 0.16mm. Available in four widths. Can be used down to -20°C (-4°F) and Temperature maximum is 60°C (140°F). Available in 8, 12, 20 and 50mm W x 20m L (.31, .47, .79 and 1.96" x 21.8 yrd). Core diameter is 76mm (3").

Prod #DescriptionUnitPriceOrder / Quote
16073
Carbon Tape, 8mm W x 20m L
each
$16.50
Qty:
16073-1
Carbon Tape, 12mm W x 20m L
each
32.00
Qty:
16073-2
Carbon Tape, 20mm W x 20m L
each
46.35
Qty:
16073-3
Carbon Tape, 50mm W x 20m L
each
92.75
Qty:

back up
3M XYZ Axis Electrically Conductive, Double-Sided Tape 9712
3M Electrically Conductive Tape
SEM micrograph

3m XYZ Electrically Conductive Double Sided Tape
magnified view of fibers

3M XYZ Axis Tape, Electrically Conductive, Double Sided, 9712 and 9713

This highly conductive double sided tape with excellent adhesion and conductivity properties has been initially developed for bonding EMI/RF shields.  Advantages of this new tape are:
 - improved adhesion - creates a solid bond and allows attachment of dissimilar materials
 - easy handling - more solid tape, conductive fibers reinforced and easier to remove
 - high conductivity - creates solid electrical connections
Due to the high electrical conductivity and excellent bonding properties these tapes are ideally suited for bonding conductive samples on SEM specimen mounts or directly on SEM specimen holders. They can be used under clean room conditions. The conductive nickel fibers extend above the adhesive ensuring a solid electrical connection between parts. It is less suitable for mounting small or powder like specimen due to the fibers in the adhesive and the topographic surface. Type 9713 has less resistance than Type 9712, see chart below:

Resistance Comparison Between Type 9712 and Type 9713
Substrate
Tested		 Aluminum/
Aluminum		 Aluminum/
Stainless Steel		 Copper/
Aluminum		 Copper/
Copper
Type 9712 <24Ω <21.5Ω <16Ω <.66Ω
Type 9713 <2.5Ω <2.0Ω <1.0Ω <0.5Ω
Based upon four wire (Kelvin probe) resistance measurements made with crossed pieces of Foil/Type 9712 or 9713/Rigid plate construction using a 1.0" x 1.0" square piece of 3M tape Type 9712 or 9713. The rigid metal surface was prepared with a Scotch-Brite™ pad to roughen the surface and cleaned with isopropyl alcohol.

XYZ highly conductive tape comes on a 76mm (3") plastic core and sizes for Type 9712 are 6.35mm, 12.7mm and 25mm W x 32.9m L (1/4", 1/2" and 1" x 36 yrd.) and for Type 9713 is 12.7mm x 32.9m L (1/2" x 36 yrd.) .

Thickness: 0.127mm (5 mil). The tape adhesive can be removed relatively easily by pulling off, rubbing or by application of packaging tape over the residual adhesive. Adhesive can be dissolved in acetone.
MSDS (PDF 24KB)

Prod #DescriptionUnitPriceOrder / Quote
16081
3M™ Type 9712 XYZ Axis Electrically Conductive, Double Sided Tape, 6.35mm W x 32.9m L
each
$21.45
Qty:
16081-2
3M™ Type 9712 XYZ Axis Electrically Conductive, Double Sided Tape, 12.7mm W x 32.9m L
each
32.40
Qty:
16081-4
3M™ Type 9712 XYZ Axis Electrically Conductive, Double Sided Tape, 25mm W x 32.9m L
each
53.80
Qty:
16081-82
3M™ Type 9713 XYZ Axis Electrically Conductive, Double Sided Tape, 12.7mm W x 32.9m L
each
49.85
Qty:

3M Z Axis Tape, Electrically Conductive, Double Sided, 9703

This is a double sided tape with high electrical conductivity. The adhesive is filled with silver coated nickel particles which results in a contact resistance of less than 0.5 ohms through the adhesive layer. Tape has low outgassing and yields excellent bonding of flat and electronic assembly applications. Use at room temperature, no thermal bonding required. Standard plastic core of 76mm (3"). thickness of liner is 0.1mm, adhesive 0.05mm.

Prod #DescriptionUnitPriceOrder / Quote
16081-10
3M™ Z-Axis Electrically Conductive, Double Sided, 9703 Tape, 6.35mm x 32.9m (1/4" x 36yrds)
each
$48.25
Qty:
16081-11
3M™ Z-Axis Electrically Conductive, Double Sided, 9703 Tape, 12.7mm x 32.9m (1/2" x 36yrds)
each
72.40
Qty:

 copper conductive tape

MSDS

3M Copper Conductive Tapes
Single Adhesive Surface"

The tape is easily cut to size and may be quickly applied to a specimen mount or other surface. Carbon or metallic coating normally is applied to the sample and mount. An electrical discharge bridge is then completed from sample, through the copper and its conductive glue to the grounded specimen mount.
The tape is dead soft copper with a conductive acrylic adhesive. It is supplied on a removable liner for easy handling and cutting. The tape offers excellent conductivity through the foil backing.
This tape is 6.3mm W x 16.46m L (1/4" x 18 yrd) or 12.7mm W x 16.46m L (1/2" x 18 yrd) and the core diameter is 76mm (3").

Foil Thickness: 0.04mm (.0016")
Total Thickness: 0.07mm (.0028")
Resistance through Adhesive: 0.005 ohm

Prod #DescriptionUnitPriceOrder / Quote
16072
3M™ Copper Conductive Tape, 6.3mm (1/4") W x 16.46m L
each
$14.90
Qty:
16072-1
3M™ Copper Conductive Tape, 12.7mm (1/2") W x 16.46m L
each
38.50
Qty:

back up
 3M copper tape double adhesivie

3M Copper Conductive Tape, Double Coated

This tape retains the features of the #16072, while enabling the investigator to attach objects to the top surface of the tape directly. The adhesive is conductive. The tape is useful, for example, in attaching insects for SEM investigation. Dimensions are 12.7mm W x 16.4m L (1/2" x 18 yrd). Core diameter is 76mm (3").
back up

Prod #DescriptionUnitPriceOrder / Quote
16074
3M™ Copper Conductive Tape, Double Coated, 12.7mm W x 16.4m L
each
$36.90
Qty:

Heavy Duty Tape Dispenser
copper conductive tape

Copper Tape, with Nickel
Single Adhesive Surface

SEM conductive tape, electrically conductive with a clean, smooth background. Nickel is embedded in the adhesive. Overall thickness is .075 mm (3.0 mil), adhesive is 0.040mm (1.6 mil). Conductive resistivity is 0.004 ohm/square. Available in 8 and 20mm W x 20m L (.315" and .787" x 21.9 yrd). Core diameter is 76mm (3").

Prod #DescriptionUnitPriceOrder / Quote
16067
Copper/Nickel Tape, 8mm W x 20m L
each
$35.00
Qty:
16067-1
Copper/Nickel Tape, 20mm W x 20m L
each
58.70
Qty:

back up
 3M Aluminum Conductive Tape

3M Aluminum Conductive Tape
Single Adhesive Surface

single coated conductive smooth surface

Scotch® 1170 tape is dead soft aluminum, is easily cut to size and may be quickly applied to a specimen mount or other surface. Carbon or metallic coating normally is applied to the sample and mount. An electrical discharge bridge is then completed from sample through the aluminum and its conductive acrylic glue to the grounded specimen mount. Foil Thickness: 0.05 mm (2.0 mil). Total Thickness (foil + adhesive): 0.081mm (3.2 mil). Electrical Resistance through adhesive: 0.010 ohm. Available in: 6.3mm, 12.7mm and 25.4mm W x 16.4m L (1/4", 1/2" and 1" x 18 yrd). Core diameter is 76mm (3").

Prod #DescriptionUnitPriceOrder / Quote
16071
3M™ Aluminum Conductive Tape, 6.3mm W x 16.4m L
each
$15.70
Qty:
16071-1
3M™ Aluminum Conductive Tape, 12.7mm W x 16.4m L
each
33.30
Qty:
16071-2
3M™ Aluminum Conductive Tape, 25.4mm W x 16.4m L
each
64.40
Qty:

 carbon conductive sheet

Carbon Conductive Sheet, Double Adhesive Coated

This electrically conductive sheet is suitable for cutting and sizing to samples, with application to SEM Energy Dispersive Spectrometry (EDS) X-ray studies. This product provides little out-gassing under vacuum. It won’t absorb or penetrate specimens, as liquid adhesives might. Sheet size: 50mm W x 120mm L x 0.16mm thick (1.97" x 4.72" x 6.3 mil)

Prod #DescriptionUnitPriceOrder / Quote
16085-1
Carbon Conductive Sheet, 50 x 120mm
pkg/10
$38.00
Qty:

back up
silver conductive sheet

Silver Conductive Sheet, Double Adhesive Coated

This highly electrically conductive sheet is suitable for cutting and sizing to samples, with application to SEM and conductive pads.

Highly conductive: Resistivity only 0.002 ohm/5mm2.

Little outgas under vacuum. Will not absorb or penetrate specimens, as liquid adhesives might absorb. Silver Sheet Size: 50mm W x 120mm L x 0.125mm thick (1.97" x 4.72" x 5 mil).

Prod #DescriptionUnitPriceOrder / Quote
16086-1
Silver Conductive Sheet, 50 x 120mm
pkg/5
$247.00
Qty:

Electro Static Dissipative Tape

Cleanroom, High Temperature, ESD Tape

This tape has a high temperature polyimide film backing and silicone adhesive. It is specially treated for enhanced electrostatic discharge performance (electrostatic dissipative). Translucent gold. It can be used up to 243°C (500°F). Standard 76mm (3") plastic core. Thickness 2.7 mil (0.07mm)

Prod #DescriptionUnitPriceOrder / Quote
16081-30
Cleanroom Tape, ESD, 6.35mm x 32.9m (1/4" x 36yrds)
each
$14.93
Qty:
16081-31
Cleanroom Tape, ESD, 12.7mm x 32.9m (1/2" x 36yrds)
each
32.40
Qty:
16081-32
Cleanroom Tape, ESD, 24.5mm x 32.9m (1" x 36yrds)
each
53.80
Qty:

High Temperature, Electrostatic Discharge Tape

Low Static, High Temperature Tape

Low Static Polyimide Film Tape, with or witout liner versions, 2.7 mil (0.07 mm), translucent, polyimide-film backed silicone adhesive tape with unique and extremely good electrostatic discharge properties. Temperature range –73° to 260°C (–100° to 500°F). Standard 76mm (3") plastic core. Thickness 2.7 mil (0.07mm).

Prod #DescriptionUnitPriceOrder / Quote
With Liner
16081-57
Low Static Polyimide Film Tape, with liner, 24.5mm x 32.9m (1" x 36yrds), each
each
$69.85
Qty:
16081-58
Low Static Polyimide Film Tape, with liner, 49mm x 32.9m (2" x 36yrds)
each
139.71
Qty:
Without Liner
16081-61
Low Static Polyimide Film Tape, without liner, 6.35mm x 32.9m (1/4" x 36yrds), each
each
15.23
Qty:
16081-63
Low Static Polyimide Film Tape, without liner, 12.7mm x 32.9m (1/2" x 36yrds)
each
31.99
Qty:


back up

Privacy Policy |
Copyright © 1996-2008 Ted Pella, Inc., All rights reserved. All trademarks are the property of their respective owners.

Page Last Updated: April 24, 2008