Hitachi Specimen Holders with M4 Thread

Single Flat Sample Clip Holder

This specimen holder is made of aluminum with spring-loaded clamping and grounding pin. Accommodates a sample thickness up to 3mm. Pin provides minimal surface clamping area and grounding on the imaged surface.

Prod #	Description	Unit	Price	Order / Quote
15375-2	Single flat sample clip holder, M4	each	$100.00	Qty:

Triple Flat Sample Clip Holder

This specimen holder is made from aluminum with spring-loaded clamping and grounding pin. Accommodates three samples with thickness up to 3mm. The pins provide minimal surface clamping area and grounding on the imaged surface.

Prod #	Description	Unit	Price	Order / Quote
15376-2	Triple Flat Sample Clip Holder, M4	each	$360.00	Qty:

45° Cross Section Holder

This Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 45° angle.  Clip width is 6.35mm. Accommodates a sample thickness up to 11mm. The clip provides minimal surface clamping area and grounding on the imaged surface.

Prod #	Description	Unit	Price	Order / Quote
15460	45° Cross Section Holder, M4	each	$100.00	Qty:

45° Triple Cross Section Holder

The Triple Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 45° angle.  Clip width is 6.35mm. Accommodates three samples with a thickness up to 11mm. The clips provide minimal surface clamping area and grounding on the imaged surface.

Prod #	Description	Unit	Price	Order / Quote
15461	45° Triple Cross Section Holder, M4	each	$250.00	Qty:

70° Cross Section Holder

This Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 70° angle.  Clip width is 6.35mm. Accommodates a sample thickness up to 11mm. The clip provides minimal surface clamping area and grounding on the imaged surface.

Prod #	Description	Unit	Price	Order / Quote
15377-2	70° Cross Section Holder, M4	each	$100.00	Qty:

Triple 70° Cross Section Holder

The Triple Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 70° angle.  Clip width is 6.35mm. Accommodates three samples with a thickness up to 11mm. The clips provide minimal surface clamping area and grounding on the imaged surface.

Prod #	Description	Unit	Price	Order / Quote
15379-2	Triple 70° Cross Section Holder, M4	each	$250.00	Qty:

90° Cross Section Holder

This Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 90° angle.  Clip width is 6.35mm. Accommodates a sample thickness up to 11mm. The clip provides minimal surface clamping area and grounding on the imaged surface.

Prod #	Description	Unit	Price	Order / Quote
15378-2	90° Cross Section Holder, M4	each	$100.00	Qty:

Triple 90° Cross Section Holder

The Triple Cross Section Holder is made of aluminum with spring-loaded brass clamping and grounding clip and holds sample at a 90° angle. Clip width is 6.35mm. Accommodates a sample thickness up to 11mm. The clips provide minimal surface clamping area and grounding on the imaged surface.

Prod #	Description	Unit	Price	Order / Quote
15380-2	Triple 90° Cross Section Holder, M4	each	$250.00	Qty:

Cross Section Holder

This specimen holder holds thin or flat samples up 6.35mm (1/4"). Adjustable angle from 0-180°.
Made of non-magnetic stainless steel. Overall height is 30mm (1.2") from the pivot point. The clamping part is a 16mm (0.62") cube w/o thumb screws.

Prod #	Description	Unit	Price	Order / Quote
15325-4	Cross Section Holder, M4	each	$90.00	Qty:

Adjustable Profile Holder

Designed to adjust the exact viewing angle for cross section made from wafers or other thin specimens up to a thickness of 3.2mm (1/8"). Angle adjustment range 0-90°. Made of aluminum with stainless steel allen screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15356-4	Adjustable Profile Holder, M4	each	$120.00	Qty:

Compact Variable Tilt Mount

This Compact Variable Tilt Specimen Mount allows for easy mounting and tilting small samples from 0° – 90° and SEM investigation with small working distances. Markings for 30°, 45°, 70° and 90°.  Table size is 11 x 11mm (0.46"x0.46"). Overall size is 14 x14 x12.7mm (0.55"x0.55"x0.5"). Made of aluminum with stainless steel screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15438	Compact Variable Tilt Mount, M4	each	$59.50	Qty:

Variable Tilt Specimen Holder for Pin Mounts

Accommodates specimens pin stubs up to 18mm (.7") diameter or with a size up to 26 x 20mm. Tilts 0 - 90° with 10° markings. Additional markings for 30°, 45°, and 70°. Tilt table size is 26 x 20mm, overall size is 33 x 20 x 19mm H. Made of aluminum with stainless steel screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15450-4	Variable Tilt Specimen Holder, M4	each	$289.00	Qty:

Variable Tilt Specimen Holder for Hitachi M4 Mounts

Accommodates Hitachi 15mm cylinder mount with M4 thread. Tilts 0 - 90° with 10° markings. Additional markings for 30°, 45°, and 70°. Tilt table size is 26 x 20mm, overall size is 33 x 20 x 19mm H. Made of aluminum with stainless steel screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15451-4	Variable Tilt Specimen Holder for Hitachi M4 mounts, M4	each	$275.00	Qty:

Accepts 15mm Hitachi mounts on pin with M4 thread. Pin can be rotated and fixed for optimum position. When the pin with M4 thread is removed, this holder also accepts a standard 12.7mm (1/2") pin stub with 3.2mm (1/8") pin. 45° gives higher SE signal w/o tilting the specimen stage. Material: machined aluminum with stainless steel Allen set screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15428-45	45° Pre-Tilt Holder, M4	each	$47.50	Qty:

Accepts 15mm Hitachi mounts on pin with M4 thread. Pin can be rotated and fixed for optimum position. When the pin with M4 thread is removed, this holder also accepts a standard 12.7mm (1/2") pin stub with 3.2mm (1/8") pin. 70° EBSD Pre-Tilt Holder w/o tilting the specimen stage. Material: machined aluminum with stainless steel Allen set screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15428-70	70° Pre-Tilt Holder, M4	each	$52.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15343-4	Springloaded Vise Clamp, M4	each	$300.00	Qty:

PELCO^® Large Universal Vise Clamp

The large and extremely versatile vise clamp is intended for large and heady samples or awkwardly shaped samples. Will clamp samples between 0-90mm. The two bases move 0-25mm. The array of holes take precision stainless steel 1/16" pins (10 pins are included) for either clamping the sample of for positioning the vise clamps (included). Overall size is 40W x 90L x 25mmH (1.6 x 3.5 x 1”). M4 threaded hole in the base.

Prod #	Description	Unit	Price	Order / Quote
15475-4	PELCO® Large Universal Vise Clamp, M4	each	$675.00	Qty:
15475-10	Replacement Vise Clamps for Large Universal Vise	pkg/2	115.00	Qty:
15475-20	Replacement Pins for Large Universal Vise, 3/4" long	pkg/10	32.50	Qty:

PELCO^® Bar Clamp Vise, 4", 6" and 8"

The PELCO^® Bar Clamp Vise is available in three lengths; 102mm (4"), 152mm (6") and 203mm (8") with the same clamps for each version. This bar type clamp can accommodate specimens up to 72mm (3"), 127mm (5") and 178mm (7") in length respectively. The jaws are reversible, offering different clamping options and they operate independently anywhere on the clamping bar. This will allow for positioning the region of interest of the specimen within the travel range of the SEM stage. Stainless steel 1/16" pins (6 pins are included) can be placed on the clamps for awkwardly shaped samples. Clamping bars and clamps can be purchased additionally to make up the best functional set for the job at hand. Made of vacuum grade aluminum with brass bar and brass thumbscrews and stainless steel type 316 dowels. M4 threaded hole in bar.

#15477-10

Overall size for the 102mm(4") version: LxWxH 102 x 22 x 19mm (4" x 7/8" x ¾") Overall size for the 152mm (6") version: LxWxH 152 x 22 x 19mm (6" x 7/8" x ¾") Overall size for the 203mm (8") version: LxWxH 203 x 22 x 19mm (8" x 7/8" x ¾")

PELCO® Technical Notes: PELCO® Bar Clamp Vise, 4, 6, and 8" (80KB PDF)

Prod #	Description	Unit	Price	Order / Quote
15477-4	PELCO® Bar Clamp Vise, 102mm (4"), complete with bar and two clamps, M4	each	$375.00	Qty:
15476-4	PELCO® Bar Clamp Vise, 152mm (6"), complete with bar and two clamps, M4	each	400.00	Qty:
15478-4	PELCO® Bar Clamp Vise, 203mm (8"), complete with bar and two clamps, M4	each	425.00	Qty:
15477-10	Additional Clamp for 102mm (4"), 152mm (6") or 203mm (8") bar	each	155.00	Qty:
15477-40	Additional 102mm (4") bar, M4	each	100.00	Qty:
15476-60	Additional 152mm (6") bar, M4	each	120.00	Qty:
15478-80	Additional 203mm (8") bar, M4	each	145.00	Qty:

PELCO Mini SEMClamp™ Ø15 x 10mm

Mini SEMclamp™ on a Ø15 x 10mm M4 cylinder mount. Convenient for holding flat or thin specimens such as Si chips, wires, foil and small tubes. Material: vacuum grade aluminum with brass screw.

Prod #	Description	Unit	Price	Order / Quote
15494	PELCO Mini SEMClamp™ Ø15 x 10mm, M4	each	$21.60	Qty:

Small PELCO SEMClamp™ 15 x 10mm

PELCO SEMClamp™ holder 15mm (0.6") long with 10mm (0.4") wide clamping area. Convenient holder for clamping down samples up to a thickness of 7mm under the clamping strips. Overall dimensions 23x20x9mm (0.9"x0.78"x0.35"). Material: machined aluminum with brass screws.

Prod #	Description	Unit	Price	Order / Quote
15347-4	Small PELCO SEMClamp™ 15 x 10mm, M4	each	$86.00	Qty:

Medium PELCO SEMClamp™ 25 x 15mm

PELCO SEMClamp™ holder 25mm (1") long with 15mm (0.6") wide clamping area. Convenient holder for clamping down samples up to a thickness of 7mm under the clamping strips. Overall dimensions 33x25x9mm (1.3"x1"x0.35"). Material: machined aluminum with brass screws.

Prod #	Description	Unit	Price	Order / Quote
15348-4	Medium PELCO SEMClamp™ 25 x 15mm, M4	each	$95.00	Qty:

Large PELCO SEMClamp™ 40 x 20mm

SEMClamp™ holder 40mm (1.6") long with 20mm (0.8") wide clamping area. Convenient holder for clamping down samples up to a thickness of 7mm under the clamping strips. Overall dimensions 48x30x9mm (1.9x1.2x0.35"). Material: machined aluminum with brass screws.

Prod #	Description	Unit	Price	Order / Quote
15349-4	Large PELCO SEMClamp™ 40 x 20mm, M4	each	$96.00	Qty:

Recessed PELCO SEMClamp™ 25 x 15mm

5mm recess allows for background free imaging and no contact with sample surface in imaging area. Clamping area is 25mm (1") long and 15mm (0.6") wide. Maximum thickness 7mm under the clamping strips. Overall dimensions 33x25x11mm 1.3"x1"x0.43"). Material: machined aluminum with brass screws.

Prod #	Description	Unit	Price	Order / Quote
15346-4	Recessed PELCO SEMClamp™ 25 x 15mm, M4	each	$96.00	Qty:

Thin Specimen Split Mount Holder

Simple but effective design to hold wafers and thin samples up to 3.2mm (1/8). 15mm dia x 10mm H. Made of aluminum with stainless steel allen screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15335-4	Thin Specimen Split Mount Holder, M4	each	$24.00	Qty:

Tube/Needle Clamp

A small tube, needle or wire clamp based on a standard Ø15x10mm cylinder mount with M4 thread. Ideal for examining wire cross sections or needle tips. Holds wires, tubes and needles up to Ø2mm (0.008"); hole is 5mm (0.20") deep. Material: vacuum grade aluminum with a stainless steel set screw.

Prod #	Description	Unit	Price	Order / Quote
15490	Tube/Needle Clamp, Ø15x10mm, M4	each	$23.50	Qty:

Large Set Screw Vise

Set screw vise with an open slot of 10mm (.394") wide x 5mm (0.197") deep. ø25mm (1") x 10mm (0.394") high. Material: machined aluminum with stainless steel set screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
16371	Large Set Screw Vise, Ø25x10mm H, M4	each	$29.90	Qty:

Large Set Screw Vise

Double Slotted Mini Vise

Double slotted set screw vise with 2 ea. 1mm wide x 3mm deep slots to clamp thin specimens or cross sections. Simple but effective design to hold wafers and thin samples up to 1mm (.039") thick. 15mm dia x 6mm H. Made of aluminum with 2 stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
16341	Double Slotted Set Screw Vise, Ø15 x 6mm H, M4	each	$21.40	Qty:

Double Slotted Mini Vise

Ø32mm Double slotted set screw vise with 2 ea. 1mm wide by 5mm deep slots. Dimensions Ø32x10mm (1-1/4" x 0.394"). Clamp thin specimens and cross sections without the need for tape or conductive paint. Material: machined aluminum with 2 stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
16313	Double Slotted Mini Vise, Ø32x10mm, M4	pkg/each	$39.90	Qty:

Large Double Slotted Vise

Large Double Slotted Set Screw Vise with 2 ea. 2.5mm by 5mm deep slots. Dimensions ø25x10 mm (1 x 0.4"). Clamp thin specimens and cross sections without the need for tape of conductive paint. Material: machined aluminum with 2 stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
16372	Large Double Slotted Set Screw Vise, Ø25mm x 10mm H, M4	each	$29.80	Qty:

Large Double Slotted Vise

Ø32mm Large double slotted set screw vise with 2 ea. 2.5mm wide by 5mm deep slots. Dimensions Ø32x10mm (1-1/4" x 0.394"). Clamp thin specimens and cross sections without the need for tape or conductive paint. Material: machined aluminum with 2 stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
16312	Large Double Slotted Set Screw Vise, Ø32x10mm, M4	pkg/each	$39.90	Qty:

Single Pin Stub Holders

For holding and viewing SEM mounts with the standard 3.2mm pin. Made of aluminum, includes a pin locking screw. Four different heights are available: 10, 25, 38 and 55mm.

Prod #	Description	Unit	Price	Order / Quote
15363-1	Single Pin Stub Holder Ø15x10mm H, M4	each	$26.50	Qty:
15363-2	Single Pin Stub Holder Ø15x15mm H, M4	each	22.50	Qty:
15387-2	Single Pin Stub Holder Ø16x25mm H, M4	each	27.50	Qty:
15361	Single Pin Stub Holder Ø16x38mm H, M4	each	25.00	Qty:
15364	Single Pin Stub Holder Ø15x55mm H, M4	each	25.00	Qty:

Multi Holder for 4 Pin Stubs

Accommodates up to four standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with stainless steel set screws. Allen wrench included. Holder size is Ø31.8 x 11.25mm.

Prod #	Description	Unit	Price	Order / Quote
15310-4	Multi Holder for 4 Pin Stubs, M4	each	$49.00	Qty:

Multi Holder for 6 Pin Stubs

Accommodates up to six standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with stainless steel set screws. Allen wrench included. Holder size is Ø42 x 10.7mm (Ø1.65" x 0.42").

Prod #	Description	Unit	Price	Order / Quote
15411	Multi Holder for 6 Pin Stubs, M4	each	$75.00	Qty:

Multi Holder for 8 Pin Stubs

Accommodates up to eight standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with stainless steel set screws. Allen wrench included. Holder size is Ø50 x 10.7mm (Ø1.97" x 0.42").

Prod #	Description	Unit	Price	Order / Quote
15413	Multi Holder for 8 Pin Stubs, M4	each	$90.00	Qty:

Multi Holder for 12 Pin Stubs

Accommodates up to twelve standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with stainless steel set screws. Allen wrench included. Holder size is Ø62 x 10.7mm (Ø2.44" x 0.42").

Prod #	Description	Unit	Price	Order / Quote
15417	Multi Holder for 12 Pin Stubs, M4	each	$100.00	Qty:

Multi Holder for 29 Pin Stubs

Accommodates up to 29 standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with 302 type stainless steel springs to hold the pin stubs. Holder size is Ø90 x 5mm (Ø3.5" x 0.2").

Prod #	Description	Unit	Price	Order / Quote
15418	Multi Holder for 29 pin stubs, M4	each	$234.50	Qty:

Multi Holder for 49 Pin Stubs

Accommodates up to 49 standard 12.7mm (1/2") pin stubs with 3.2mm (1/8) pin. Made of aluminum with 302 type stainless steel springs to hold the pin stubs. Holder size is Ø117 x 5mm (Ø4.6" x 0.2").

Prod #	Description	Unit	Price	Order / Quote
15419	Multi Holder for 49 pin stubs, M4	each	$394.50	Qty:

45° Multi Holder for 6 Pin Stubs

Prod #	Description	Unit	Price	Order / Quote
15429	45° Multi Holder for 6 pin stubs, M4	each	$108.00	Qty:

Cylinder Holder, 22mm (7/8")

Specimen holder for cylinders up to 22mm (7/8") diameter. Made of aluminum with stainless steel allen screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15402	Specimen holder for cylinders up to 22mm (7/8"), M4	each	$39.00	Qty:

Metallographic Mount Holder, 1" or 25mm

Specimen holder for 1" or 25mm metallographic mounts. Made of aluminum with stainless steel allen screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15403	Metallographic Mount Holder, 1" or 25mm, M4	each	$46.00	Qty:

Metallographic Mount Holder, 1-1/4" or 30mm

Specimen holder for 1-1/4" or 30mm metallographic mounts. Made of aluminum with stainless steel allen screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15404	Metallographic Mount Holder, 1-1/4" or 30mm, M4	each	$58.00	Qty:

Metallographic Mount Holder, 1-1/2" or 40mm

Specimen holder for 1-1/2" or 40mm metallographic mounts. Made of aluminum with stainless steel allen screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15405	Metallographic Mount Holder, 1-1/2" or 40mm, M4	each	$68.00	Qty:

Metallographic Mount Holder, 2" or 50mm

Specimen holder for 2" or 50mm metallographic mounts. Made of aluminum with stainless steel allen screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15406	Metallographic Mount Holder, 2" or 50mm, M4	each	$74.00	Qty:

Geological Thin Section Holder

Holds a standard geological thin section or slide of 47 x 27mm. 2 clips are provided for secure holding. Tweezer inserts enable easy loading. Overall dimensions are 55 x 30 x 8mm. Material: aluminum with copper clips and brass screws.

Prod #	Description	Unit	Price	Order / Quote
15431-4	Single Geological Thin Section Holder, M4	each	$216.00	Qty:

Variable Size Geological Thin Section Holder

This variable size geological thin section holder holds either standard thin sections of 47 x 27mm or smaller or larger thin sections. Smallest size would be 40x20mm. Two clips are provided for secure holding. Tweezers insert enables easy loading. Overall dimensions are 51 x 32 x 8mm. Material: vacuum grade aluminum with copper clips and brass screws.

Prod #	Description	Unit	Price	Order / Quote
15435-4	Variable Size Geological Thin Section Holder, M4	each	$216.00	Qty:

Dual Geological Thin Section Holder

Holds two standard geological thin sections or slides of 47 x 27mm. Tweezer inserts enable easy loading. Clips are provided for secure holding. Overall dimensions are 55 x 58 x 8mm. Material: aluminum with copper clips and brass screws.

Prod #	Description	Unit	Price	Order / Quote
15432-4	Dual Geological Thin Section Holder, M4	each	$246.00	Qty:

Quadruple Geological Thin Section Holder

Holds four standard geological thin sections or slides of 47 x 27mm. Tweezer inserts enable easy loading. Clips are provided for secure holding. Overall dimensions are 107 x 58 x 8mm. Material: aluminum with copper clips and brass screws.

Prod #	Description	Unit	Price	Order / Quote
15434-4	Quadruple Geological Thin Section Holder, M4	each	$272.00	Qty:

PELCO SEMClip™ Replacement Clips and Screws

Prod #	Description	Unit	Price	Order / Quote
16399	PELCO SEMClip™ Clips	pkg/10	$75.00	Qty:
16399-10	PELCO SEMClip™ Screws, Brass, M2 x 3mm length	pkg/10	18.75	Qty:

Round Bulk Specimen Holder

The bulk specimen holder holds irregular and round specimens up to a diameter of 32mm (1-1/4"). Made of aluminum with two sets of stainless steel allen screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15308-4	Round Bulk Specimen Holder, M4	each	$85.00	Qty:

Large Round Bulk Specimen Holder

The large bulk specimen holder holds larger irregular and round specimens up to a diameter of 51mm (2"). Made of aluminum with two sets of stainless steel allen screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15423	Large Round Bulk Specimen Holder, M4	each	$104.00	Qty:

Straight Bulk Specimen Holder

Versatile specimen holder to clamp irregular or long shaped specimens. Opening is 15.9W x 25.4L x 9.5mm D (5/8" x 1" x 3/8"). Made of aluminum with stainless steel allen screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15320-4	Straight Bulk Specimen Holder, M4	each	$82.00	Qty:

Large Bulk Specimen Holder

Opening is 32mm (1-1/4") wide x 32mm (1-1/4") long x 13mm (1/2") deep. Material: machined aluminum with stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15321-4	PELCO® Large Bulk Specimen Holder, M4	each	$96.00	Qty:

X-Large Bulk Specimen Holder

for up to 2" specimens

Opening is 52mm (2") wide x 40mm (1-1/2") long x 13mm (1/2") deep. Material: machined aluminum with stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15322-4	PELCO® X-Large Bulk Specimen Holder, M4	each	$124.00	Qty:

XX-Large Bulk Specimen Holder

for up to 3" specimens

Opening is 80mm (3-1/8") wide x 48mm (1-7/8") long x 13mm (1/2") deep. Material: machined aluminum with stainless steel allen set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15323-4	PELCO® XX-Large Bulk Specimen Holder, M4	each	$148.00	Qty:

Multipurpose Specimen Holder

Accepts up to 25.4mm (1") diameter specimens. The slotted design also allows for clamping elongated or rod shaped specimens. Made of aluminum with stainless steel allen screw. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15305-4	Multi Purpose Specimen Holder, M4	each	$62.00	Qty:

45°/90° Combination Holder

Combined specimen holder for 90° cross sections of wafers or thin samples up to 6.35mm (1/4") and a pin stub at 45°. Made of aluminum with stainless steel set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15358-4	45° / 90° Combination Holder, M4	each	$94.00	Qty:

TEM Grid Holder for Hitachi M4

This TEM grid holder holds up to 4 TEM grids. It enables imaging and analyzing specimens on TEM grids in the SEM. For EDS applications it is beneficial to place thin films on a TEM grid or small particles on a TEM grid with a support film. This can significantly reduce background in the EDS spectrum and increase detection limits of the EDS detector. Opening angle on the holes in the top and base are 120° to reduce electron scattering and improve X-ray collection. Overall diameter is 18mm (0.7"), overall height is approximately 25mm (1") with a stand-off pin mounted on a ø15x10mm x M4 Hitachi mount. The stand-off pin minimizes electron and X-ray scattering contribution from the stage. TEM grid locations are numbered. Material: vacuum grade aluminum with brass screw.

Prod #	Description	Unit	Price	Order / Quote
15469-15	TEM Grid Holder for 4 Grids, M4	each	$196.00	Qty:

E-Beam Lithography Mount

The E-Beam Lithography Mount comprises 2 PELCO SEMClips™ to hold the sample, a Faraday cup (ø2.5mm with 100µm hole) to measure the beam current and gold on carbon resolution sample (ø3mm) for resolution test all on a 25mm aluminum cylinder stub positioned in such a way to leave maximum sample space. The Gold on Carbon is similar to #617 with gold particle size range from approximately 5nm to 150nm. M4 threaded hole in bottom. Material: Aluminum with copper clips and brass screws.

Prod #	Description	Unit	Price	Order / Quote
16405-4	E-Beam Lithography Mount, M4	each	$485.00	Qty:

Hitachi Multiple Specimen Mount Holders

A set of useful holders to quickly mount multiple standard ø15mm Hitachi mounts with M4 thread on a base with M4 thread. Fully compatible with all Hitachi stage adapters using M4 thread. Available for 3 of 6 Hitachi mounts, flat or with 45° tilt for enhanced signal. Made of aluminum with stainless steel M4 threads.

Prod #	Description	Unit	Price	Order / Quote
15433	Triple Specimen Holder for 3 Hitachi mounts, Ø25x6mmxM4	each	$40.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15436	Multiple Specimen Holder for 6 Hitachi mounts, Ø35x6mmxM4	each	$76.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15437	Multiple Specimen Holder for 3 Hitachi mounts, Ø35x6mmxM4	each	$76.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15430-3	45° Tilt Triple Specimen Holder for 3 Hitachi mounts, Ø25x14mmxM4	each	$68.00	Qty:

Prod #	Description	Unit	Price	Order / Quote
15430-6	45° Tilt Multiple Specimen Holder for 6 Hitachi mounts, Ø35x14mmxM4	each	$115.00	Qty:

Multi Holder for 5 JEOL Stubs

Holds up to five 9.5mm JEOL cylinder mounts. Made of aluminum with stainless steel set screws. Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15315-4	Multi Specimen Holder for JEOL Stubs, M4	each	$62.00	Qty:

JEOL or ISI/ABT/Topcon mounts to Hitachi M4 mount

Small cylinder mount adapter accommodates JEOL or ISI/ABT/Topcon cylinder mounts up to 15mm diameter. Enables the use of Ø9.5 and Ø12.2mm JEOL or Ø15mm ISI/ABT/Topcon cylinder mounts on Hitachi M4. Made from aluminum with stainless steel screw, Allen wrench included.

Prod #	Description	Unit	Price	Order / Quote
15401	Adapter Holder for Cylinder Mounts, M4	each	$36.00	Qty:

300mm (12")

200mm (8")

Prod #	Description	Unit	Price	Order / Quote
15393	Wafer Holder for notch style wafers, 100mm / 4", M4	each	$425.00	Qty:
15391	Wafer Holder for notch style wafers, 150mm / 6", M4	each	450.00	Qty:
15395	Wafer Holder for notch style wafers, 200mm / 8", M4	each	850.00	Qty:
15394	Wafer Holder for notch style wafers, 300mm / 12", M4	each	950.00	Qty:

Hitachi Stub Extensions

Hitachi Stub Extensions with M4 thread (top and bottom) are intended toaccomodate shorter working distance in the SEM. Available in 12, 18, 25mm. Stub extensions can be stacked. Material: brass with stainless steel M4, complete with aluminum locking nut.

Prod #	Description	Unit	Price	Order / Quote
15373-2	Short Stub Extension, 12mm, with Locking Nut	each	$42.50	Qty:
15365-2	Medium Stub Extension, 18mm, with Locking Nut	each	42.50	Qty:
15374-2	Long Stub Extension, 25mm, with Locking Nut	each	42.50	Qty:
15373-22	M6 Locking Nut for Stub Extensions, Aluminum	each	15.00	Qty: